Home > Tripods & DSLR Rig > DSLR Rig >

Lanparte Motorised Motion Control E-Slider for Smooth Video Recording, ESV-1
Lanparte Motorised Motion Control E-Slider for Smooth Video Recording, ESV-1


 
Alternative Views:
Our Price:$1,650.00


Product Code: LANPARTE-ESV01-SLIDE
Qty:

Description What Is Included
 
Effective Length: 100cm Motorized slider; Support up to 65lbs Wired 3-mode Motion control Quiet and smooth video recording.
Specification
      • Motorized Slider
      • Support Up To 65Lbs
      • Quiet and smooth video recording
      • Nominal Dimesions: 140cm (L) x 10cm (W) x 10cm (H) - 55inch (L) x 4inch (W) x 4inch (H)
      • Connect: 3/8" male thread on plate; 1/4" & 3/8" female thread on slider bottom
      • Power: 11 to 20 Volts DC input

      Features:
      • Adjustable Terrain Legs
      • Multiple 1/4inch & 3/8inch thread-ins compatible with industry standard tripods
      • Offset Mounting Plate
      • Power Options: Compatible w/ V-Lock system

      ESV1 user manual

      ESV1 has three modes
      1. MT( manual transmission)
      2. AT (Auto transmission；
      3. Rec (motion capture)

      • Power/Data indicator
      Power indicator: turn on the power button on the back side of the controller, the power indicator will turn yellow, once the power indicator turns red that will mean it is out of power at which point you will need to replace/recharge the battery.
      Data indicator : once the moving base works the data indicator will turn yellow and blink, the faster the moving base moves the faster the data indicator will blink.

      • Speed grade
      You can use speed grade up/down buttons to control the speed grades(just like driving an MT car: the higher gear you use the faster the car goes)
      Press the SP(down) button, the speed grade indicator will then move to the left, and then the speed grade will move down;
      Press the SP(up) button, to move the speed grade indicator to the right, then move the speed grade up;
      Note: you cannot change the speed grade unless the data indicator is off.

      • Mode
      The mode of ESV1 uses Rolling cycle methods. You can only change the mod when the data indicator is off. Press the “mode” button to change it: MT, AT, REC, when you selected the mode, the indicator on the corresponding light will on.

      The rolling cycle methods refers to when the Red button is pressed changing the rolling cycles to: MT,AT,REC,MT,AT…..

      • End switch
      Independently of which mode it is on once the moving base reaches the 'end switch trigger' it will stop immediately. Please note for reference the left side of the slider is the one closer to the power supply system and is also the “start point”. The right side is the opposite side, furthest from the power supply system”.

      • MT mode:
      1. Set the speed grade
      2. Use the manual control bar to control the moving base, press the L or R to make it go left or right. The harder you push the bar, the faster the moving base goes.
      3. Once the moving base reaches the “end switch” the moving base will stop;
      Note: on the MT mode the 4/ 5/ 6 buttons are useless

      • AT mode:
      1. Set the speed grade
      2. Turn the auto speed knob 6 to set a moving speed;
      3. Press L or R to select a moving direction;
      4. Press the play/pause button to make the moving base move;
      5. When the moving base is working, you can turn the auto speed knob 6 to adjust speed;
      6. When the moving base is working press the play/pause button to stop it, press it once again to make it move;
      7. After the moving base leaves the start point press the recall button to make it return to the start point
      Note: on the AT mode, the manual control bar 2 is useless

      • Rec mode(motion capture)
      1. Set the speed grade
      2. Press the “rec” button to prepare recording, the indicator of “rec” button should turn red;
      3. Use the manual control bar to control the moving base. Once the moving base moves the 'data' and 'rec' indicator blinks;
      4. Press the 'rec' button again to stop recording, at which point the moving base will return to the 'start point' automatically;
      5. At this point the 'track' is saved. By pressing the play/pause button the movement will be repeated. Press the play/pause button to play/pause the movement during the memorised sequence.

      • Remove a saved track
      Method 1: hold the “recall” button for three seconds, the three indicators on the control buttons will all flash
      Method 2: press the “rec” button once again. The three indicators on the control buttons all flash

            Share your knowledge of this product with other customers... Be the first to write a review

            Browse for more products in the same category as this item:

            Tripods & DSLR Rig > DSLR Rig